RYCOTE 033702 INVISION SOFTIE LYRE MOUNT For microphones 19-34mm in diameter, with pistol grip

Modular suspension provides support for the microphone and the other accessories. It is a central bar fitted with two Lyre clips. The microphone is supported by the Universal Lyre clips (for microphones between diameters of 19-25mm). There are four different bar (module) lengths; 1, 2, 3 correspond to small, medium and large respectively. Half module types are a special case. See below. Sizes 1, 2 and 3 are moulded from a black, reinforced glass polymer incorporating a UV stabilizer to prevent UV light deterioration and a rubber additive to prevent it being brittle, making it up to 60% stronger than the alternative metal bar. Other sizes are made from machined aluminium and hard-anodized in black.

'Mono' type single microphone body have two Lyre clips, to take a single microphone body. The name 'Mono' should be treated with caution since it refers to the suspension holding a single microphone which may be either mono or stereo. They are offered in three different sizes, each of which can accommodate various different microphones by using five different varieties of Lyre suspensions. Please see the compatibility chart below to select the appropriate size.

'Stereo' types – for one or two microphone bodies have two Lyre clips, to take a single microphone body, and, in general, are supplied with back-to-back clips to suit two microphone bodies mounted parallel to each other. The term 'Stereo' should be treated with caution, because certain larger single-body mono microphones require the larger diameter windshield and accessories in order to fit.

Included accessories: Pistol-grip with 3/8″ thread socket, lightweight boom adaptor (also 3/8″ socket), a clip-on XLR holder, a set of virtually unbreakable Universal Lyres for 19-25mm diameter microphones, a pair of square MKH Lyre clips and a hex key for adjustments.

Optional accessories: Connboxes, Modular Windshields, Hi Wind covers, Windjammers. Lyre clips for microphones with larger diameter (30mm) must be used with some models, with heavier microphones requiring grey, 30mm, 'heavy duty' lyre clips.

Versions 040139, 040144, 040146, and 040151 also include CB 1 Connbox with 3-pin female XLR termination.

This table contains details of suitable suspensions for some common microphones and microphone combinations. For assistance in selecting an Invision suspension to suit alternative microphones, please contact Technical Support.

Note: The suspension types in the above table have standard lyres. A suspension with harder-grade lyres, the INV-7HG-MKIII, is available to fit the same size microphones as INV-7 and INV-8 that have a heavier weight.

These members of the InVision range are shock-mount and suspension systems for fitting microphones between 9.5 and 25mm in diameter and up to 300mm in length, depending on model, to camcorders and digital SLR cameras. Most are fitted to the camera hot-shoe; others screw into a standard quarter-inch thread, available on some camcorders, or by means of separately available adapters.

In each case the microphone is suspended in two of Rycote's W-shaped patented Lyre mounts, which provide 'substantially better isolation from camera motor and drive noise and vibrations than traditional on-camera microphone mounts'. Since there are no elasticated parts, the mounts never sag or need re-threading.

042901 - Hot Shoe

A 'universal' plastic clip is supported by two Lyres which are in turn supported by a 'modular' bar. The modular bar includes a moulded cable clip, and is connected to one end of a transverse bar by a bolt with thumbscrew. The modular bar can swivel on the transverse bar and be moved along it's length and then fixed in position using the thumbscrew. At the other end of the transverse bar a hot-shoe adapter is fitted using a thumb-screw about which it can swivel a full 360 degrees in the horizontal plane. As a result the microphone can be positioned as desired in the horizontal plane, but remains fixed in the vertical plane.

The universal clip is suited to microphones 19 - 25mm in diameter and up to 300 mm in length.

042902 - 1/4 inch Adapter

Substantially the same as the 042901, this model does not have a hot shoe mount, it is substituted by a standard quarter-inch threaded screw which fits to a female thread and is locked using a thumbscrew. It is otherwise the same.

InVision USM series studio mounts use Rycote’s patented ‘Lyre’ technology to suspend studio microphones safely, and isolate them from the low-frequency thumps and rumbles that are transmitted through microphone stands. Due to the superior self-damping of the ‘Lyres’ they offer much better isolation across the whole audio spectrum, particularly in the 40-70 Hz region, than conventional elastic suspensions, which can sometimes have a negative effect at these critical frequencies, if not matched to the particular microphone. The mounts are designed to provide equal isolation around 360 degrees and are thus suitable for all side-address microphones; omnidirectional, cardioid or figure-of-eight microphones can be oriented vertically or horizontally.

Microphones are locked in the mounts by four soft, rubber grips on the end of precision-made stainless-steel thumbscrews with ridged plastic heads. The screws can be adjusted by hand to fit almost any shape and profile within 18-55 mm. The grip surface of the pads allows the mounts to hold the microphone securely, even when positioned head-down, with minimal pressure from the screws. Note that microphones must be fitted into the mounts so that their centre of gravity is close to the level of the outer ring of the mount.

Note (1): maximum

Common specifications

Suspension weight: 154g. Overall diameter: 120mm. Length: 170mm. Depth: 70mm. Suspension rotation: 175 degrees. Thread: 3/8 and 5/8 inch.

This table contains details of suitable suspensions for some common microphones and microphone combinations. The table also shows the orientation for mounting with any particular microphone and suspension combination. For assistance in selecting an Invision USM suspension to suit alternative microphones, please contact Technical Support.

Each kit includes a single InVision USM suspension along with a single InVision Universal Pop Filter.

Kit contents