NEUTRIK NDO DUMMY PLUG, Opticalcon

The ruggedised, all-metal connector body houses twelve fibre ends, terminated in an MTP female body (interface with locating pin receptacle holes). It has a simple push-to-latch mating action; a pull-to-release outer sleeve allows un-mating. It incorporates a heavy-duty cable retention mechanism which attaches to the aramid yarn within the cable. In addition to the automatic sealing shutters, a rubber-coated, steel, latching protective cap is fitted for use when unmated. When mated or capped, the connection is environmentally sealed up to IP65 (see chassis connector sealing options). Inserts are colour-coded to indicate multimode (black) and singlemode APC (green).

Note: Cable connectors are pre-assembled onto cable and are not available as individual components.

ADVANCED MTP - 12M, 12SA

Twelve-fibre, lightweight, mobile, field cable with rugged PUR jacket and excellent cable retention provided by an aramid yarn wrap. Available in multimode (12M), or singlemode APC (12SA) versions. With military approval, it is suitable for demanding audio and broadcast applications.

ADVANCED MTP X-TREME - X12M, X12SA

Twelve-fibre 'X-TREME' mobile field cable with a PUR (outer) cut-proof and rodent-resistant double jacket/glass yarn sandwich construction. Excellent cable retention is provided by an aramid yarn wrap. Available in multimode (X12M) or singlemode APC (X12SA) versions.

Cable assemblies are supplied either in an airspool, a case, or on a drum according to length or requirement.

Connector spring and coding ring colour options are available for channel identification, please specify at time of enquiry.

Due to the large number of possible configurations, lengths, colour-coding combinations and packaging options, only a representative range of standard assemblies is listed here. Please contact Sales or Technical Support to discuss your exact requirements and options.

NO12FDW-A

The chassis connector acts as a 'feed-through' and accepts a conventional MTP male (interface with locating pins) MM or SM APC connector at the rear. It has an integral, automatic, sealing-shutter, with silicone gaskets to protect the fibre ends and block laser emissions when unmated. The sealing shutter is colour-coded orange to identify it as MTP. Additional NDO rubber push-fit dummy plugs or semi-latching SCNO-FDW-A metal sealing covers are recommended for chassis connectors when not in use.

The connectors must be mounted on the front of cases, bulkheads or panels in a standard Neutrik 'D' cut-out. If mounting in a sixteen-way Canford 'Universal Connection Panel', it is strongly recommended that the connectors are spaced alternately (horizontally) with blanking-plates, to allow sufficient access to the cable-connector latching-sleeve. The eight-way Canford 'Universal Connection Panel' has cut-outs equally spaced across the width of the panel and will accommodate opticalCON connectors in every position.

A sealing gasket may be fitted behind the connector flange where environmental sealing up to IP65, when mated, is required. They are not required for sealing in wallbox, tailgate or termination panel applications, where the panels themselves are not sealed, However, the gaskets provide easy colour identification of the fibre mode; multimode (black) or singlemode (blue). Red, green, yellow and white gaskets provide channel identification. Gaskets should be ordered separately as required.

Note: The sealing gaskets are larger than the connector flange making them unsuitable for use on panels with designation strips and / or conventional 'D' cut-out separation (16 cut-outs in a 19 inch panel).

Dedicated, Canford manufactured, 2U, flat or angled panels are available, to accommodate up to 8 connectors with gaskets. See Tailboard and wallbox termination panels. Modular 1U and 3U angled-panel systems are also available, see NEUTRIK OPTICALCON ADVANCED Z-PANELS and ANGLED RACK PANELS. Additional NDO dummy plugs are also recommended for chassis connectors when not in use.

NAO12

These allow opticalCON MTP cables to be joined inline; they are IP65 rated when mated.

These assemblies are required to connect the opticalCON MTP chassis connector to equipment within the rack or system. Due to the many possible length and breakout requirements they are made to order in the UK to specific requirements, usually within 5 days but may be supplied more quickly if required and dependant on factory capacity.

Typically an assembly would consist of an MTP male (with locating pins) suitable for mounting from the rear in the opticalCON MTP panel mount connector, and either a 12-core fibre to an MTP male or female 12-core connector with mating housing, or to a breakout or fan-out terminated with individual LC, SC, ST or E2000 connectors. Multicore and breakout length or lengths may be individually specified. Please contact Sales or Technical Support for details.